Springtime Snowmobile Trailer Maintenance

Spring is the time to slather parts of snowmobile trailers in lightweight oil and grease to protect it from corrosion over the summer. Taking, literally, a few minutes now to work some preventive maintenance into your springtime ‘to-do’ list will help prevent serious corrosion that could take hours to repair in the fall. Here are a few for springtime snowmobile trailer maintenance:

Snowmobile tie-down bar threads should be coated with anti-seize before long-term storage.

1. Spray the vertical tube of the tongue jack with WD-40 or similar, lightweight oil and then crank the jack up and down a few times to coat the metal surfaces with oil. Don’t forget to shoot the little plastic wheel’s axle so it continues to roll easily. If your tongue jack has a grease zerk, pump a shots of grease into it to keep it working smoothly.

2. Coat the tie-down bar cranks with anti-seize lube so they don’t rust over the summer. If your trailer has a ramp that’s secured to the trailer with a crank, do the same to protect those threads.

3. Douse the coupler assembly with oil and operate it a few times to work the oil throughout the mechanism. Hose down the safety chains, too.

4. If you have the means, raise the trailer off the ground and set the axle on wood blocks or bricks, and then lean a piece of plywood against each wheel. This will protect the rubber from the sun’s UV rays that cause dry rot.

While many snowmobile trailer hubs have grease zerks to make maintenace easier, they should be disassembled and inspected annually.

5. Most snowmobile trailers have greaseable wheel hubs that makes it easy to stay on top of maintenance. Pump a few shots of fresh grease into the hubs to displace water and lube the bearings. Some trailer axles have a small hole on the back of the hub so the old grease can be flushed out. Have a helper watch this area as you pump the grease gun until clean grease comes out, or you might be able to hear it crackle and pop as it oozes out.

At a minimum, the five snowmobile trailer maintenance tips listed above should be performed now. If you’re more ambitious, wash the trailer, too. Use a pressure washer to clean the deck — top and bottom surfaces — and rinse off the salt and grime that accumulated on the frame and wheels. Enclosed trailers should be washed with a soft-bristle brush and soap and water to preserve the finish.

 

3 thoughts on “Springtime Snowmobile Trailer Maintenance

  • Avatar for RICHARD G. Maaske

    ARCTIC CAT SNOWMOBILES HAVE A BAD TIME BLOWING DRIVE BELTS. Back in the years 1989 to 1999. IT WAS VERY SELDOM, IF AT ALL. You would blow a Belt. I know, beause I owned a 1989, 1990 1991 wildcats. And I still own the 1991 wildcat 700. And a 1995 ZRT-800. And are in great shape. And my son had a 1989+1990 Wildcats. He has 2003 ZR 800. And back than ,the secondary clutches floated back forth , on the jackshaft. I have my ,secondary clutches floating .085. AND MY SON,S ZR-800 . IS floating too. And in all the years ,we never have blown, any Belts. And we have the snowmbiles . AT speeds over 100 MPH. Driven in deep snow. And NO BLOWN BELTS! WE only, changed the drive Belts. When they wore narrow in width. Than we were not getting ,the best perforance out of our snowmobile. With the secondary clutch floating. It can follow alone with the primary drive clutch. And it will , keep the drive Belt . From being at a angle. At any time as it shifts out, less heat build up in the drive Belt.

    Reply
  • Avatar for Tyler Meredith

    I like what this article recommends about doing things like lubing the bearings and couplers. It makes sense that keeping the trailer lubricated during the winter could be helpful to make sure no water gets into the assembly and causes rust. It’s something to remember to make sure the trailer is able to transport the snowmobiles effectively without breaking down.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *